JURISPROFESSIONALINSTRUMENTS

Exhibit A

The Corporation has been advised that its records are hard to read. This exhibit restates them plainly, once. Where it and the case files disagree, this exhibit is the one written for people.

Made
By hands and machines in Portland, Oregon
Builder of record
Grant Thomas
Correspondence
[email protected] · @juris_instruments · answered by the builder, by name
Instruments
C-75 (waitlist open) · C-75A, C-75T (drawn, not yet built)
Before you commit
Photographs of the prototype are below. Recordings will be entered into the record here.
The C-75 prototype from the tailpiece end: black-dyed top, brass bridge, trapeze tailpiece, amber knobs, the neck running away. The C-75 prototype at three-quarters: the beveled edge worn through to bare wood where the arm rests, mahogany sides. The C-75 prototype from above: the full angular body, two pickups, bridge, tailpiece and the fingerboard with side dots only.
The prototype, as built: black dye under garnet shellac. The headstock badge is a prototype and does not match the production design. The edge wear is real.
ExhibitA Sheet1 of 3
02

The C-75, plainly

The one now allocating
PriceUSD 2,500 for the first five (serials 001–005). Later runs will be priced separately.
AvailabilityFive this year, built to order. The waitlist is open now; serial numbers will follow its order.
Lead timeAbout six months from deposit: 90 days for the body and neck to be made, then 12 weeks of finishing and assembly in Portland.An estimate, given in writing when your build starts.
BodyMahogany, 2.0" deep, with a 0.2" maple cap. One U-shaped chamber through both wings and across the lower bout; a solid centre block carries the pickups and bridge.
Edges5/8" flat bevels on the top and back, leaving a 3/4" band round the side. Where the top bevel cuts through the cap, the maple shows as a natural line round the edge.
Size18.00" long · 13.49" across the lower bout
NeckMahogany, set and glued at 4°. Meets the body at the 16th fret.
Neck carve’59 roundback, shared by all three models. 0.86" deep at the 1st fret, 0.96" at the 12th.
NutGraph Tech, 1-11/16" (42.9 mm) wide.
FingerboardEbony, 12" radius. No dots on the face; side dots only.
Frets22, nickel silver, 6105 wire (0.090" wide, 0.055" tall).
Scale24.75"
Headstock3+3, tilted back 11.2°. Truss rod adjusted through a slot above the nut, under a rosewood cover. Riveted asset tag.
TunersGrover Deluxe 133N, nickel, three per side.
PickupsTV Jones T-Armond, two, English mount.The prototype carries no-ear pickups; production instruments get English-mount T-Armonds.
BridgeBrass Compton, one-piece and compensated, on brass thumbwheels over a rosewood base.
TailpieceAllparts short trapeze.
VibratoNot offered. The C-75 is designed around the trapeze and the Compton bridge, not a vibrato.
ControlsA volume for each pickup, amber speck ribbed knobs. No tone knob: a full-size three-way tone switch between them gives three fixed settings (open, .0039 µF, .012 µF); pickup selector on the bass horn. Both switches under skirted dress nuts.
JackElectrosocket, treble side.
FinishGarnet shellac, applied by hand, under a hard wax oil. No lacquer.Shellac is a soft, repairable finish. The hard wax oil on top adds protection and makes it last longer before it wears through where your arm rests. Both coats can be refreshed.
ColoursBlack dye on the maple top (as built): under garnet shellac it reads as a warm black. Or natural maple. Solid colours in milk paint: aged computer white, primer grey. All are finished in garnet shellac. Painted tops keep the maple line round the edge.
Weight6.55 lb, calculated from the model. Your guitar is weighed on a scale before the balance is due.
Strings and setupStringjoy Flyers flatwounds, .012 to .052 with a plain .020 3rd, as on the builder’s own. Action 2.0 mm (5/64") at the 12th fret.
CaseUnder review.
C-75A “The Amicus”
StatusDesigned and drawn. None built yet; no units allocated.
PriceNot set.
In shortArchtop. Faceted Port Orford cedar top, one-piece alder rim, arched bigleaf maple back. Maple set neck with the C-75’s ’59 roundback carve, Richlite board, 22 nickel-silver 6105 frets, 24.75" scale. One EMG 91 hung from the board (Novak gold foil as an alternative). About 4.0 lb, calculated.
C-75T
StatusDesigned and drawn. None built yet; no units allocated.
PriceNot set.
In shortSolid ash body on the C-75 outline. Bolt-on maple neck with the C-75’s ’59 roundback carve, ebony board, 12" radius, 21 nickel-silver 6105 frets, 25.5" scale. Two T-type pickups, three-saddle string-through bridge. Angled headstock with a volute, so no string tree. About 7.7 lb in swamp ash, calculated.
ExhibitA Sheet2 of 3
03

Deposits and terms

Plainly

When your serial comes up, a USD 700 deposit reserves it. The balance, USD 1,800, is due when the guitar is finished, before it ships.

The deposit pays for machining the body and neck. You can have it back in full, for any reason, until that machining is ordered. After that the money has been spent on your guitar and isn’t refundable. Nothing is taken to join the waitlist.

To buy one, join the waitlist: an email address, nothing else, and no commitment. When allocation of the C-75 opens, the waitlist is written to first, in order of entry, with a requisition form. A requisition is made by a USD 700 deposit, refundable until machining is ordered.

Questions: [email protected]. Grant answers, by name.

Join the waitlist

JURISPROFESSIONALINSTRUMENTSRes ipsa non loquitur
ExhibitA Sheet3 of 3

A World’s Very First production