C-75T
Designation withheld
A solid-body stringed instrument on outline C-75. Bolted neck of 25.5 scale; pickups, bridge and controls of the T type. The disclosure relates generally to music, and specifically to an established precedent.
| Item | Part | Specification |
|---|---|---|
| 10 | Body | Ash, solid, one or two pieces. 2.0 deep on outline C-75. |
| 40 | Neck | Maple, bolt-on. ’59 roundback. Standard heel. Headstock at 11.2° with volute. |
| 42 | Fingerboard | Ebony, 12 radius. |
| — | Frets | 21, nickel silver, 6105. |
| — | Scale | 25.5. |
| 20 | Bridge | Three-saddle plate. Strings through the body. |
| 22 | Bridge pickup | T type, on its baseplate. |
| 24 | Neck pickup | T type, chrome cover, on springs. |
| 30 | Controls | 5-1/2 in plate: three-way switch, volume, tone. |
| 34 | Jack | Cup jack. |
| 44 | Tuners | Grover, three per side. |
| — | Finish | Shellac, then oil and wax, rubbed by hand. Solid colours in milk paint beneath. |
| Rev | Description |
|---|---|
| A | Filed. Designation withheld pending review. |
- Dimensions in inches; angles in degrees. DO NOT SCALE DRAWING.
- No unit has been produced. Mass is calculated. It excludes the OPERATOR.
- The middle of the tail is left square. This is intended.
- No string tree is fitted. None is required. See Claim 4.
- Designation withheld pending review. Refer to the instrument as the C-75T.
As defined in C-75-001, Sheet 1, with the following additions.
- Precedent
- An earlier instrument whose arrangement is followed. Not cited by name.
- The recess that receives the neck. Standard pattern.
- Machined surfaces
- ±0.005
- Scale
- 25.5. Not to be confused with 24.75.
- Pitch
- Per OPERATOR. Not inspected.
- Non-billable hours
- No upper limit established.
Drawings
Claims
What is claimed is:
- A stringed instrument comprising a solid body (10) 2.0 deep on outline C-75, a neck (40) attached by bolts, and a scale of 25.5.
- The instrument of claim 1, beveled 5/8 top and back, leaving a 3/4 square band, the middle of the tail left square.
- The instrument of claim 1, the neck seated in a pocket of the standard pattern at the sixteenth fret, such that any neck made for that pocket would fit it, and no such neck would have its headstock.
- The instrument of claim 1, the headstock inclined at 11.2° with a volute, whereby no string tree is required.
- The instrument of claim 1, having twenty-one (21) nickel-silver frets on an ebony fingerboard (42) of 12 radius.
- The instrument of claim 1, having a bridge pickup (22) in a three-saddle plate (20), strings passing through the body, and a covered neck pickup (24) on springs.
- The instrument of claim 1, having a control plate (30) parallel to the treble bevel, and a jack (34) on the flat of the treble lower bevel, where Case No. C-75 carries its own.
- The instrument of claim 1, no pickguard being present.
Conditions of use
Form JPI-75T- For use outside BILLABLE HOURS.
- The scale exceeds that of the C-75 by 0.75. OPERATORS moving between instruments shall allow for this.
- The neck (40) is bolted. It may be removed. Removal is not a condition of use.
- The precedent for this instrument shall not be cited by name.
- Hours of operation are recorded as NON-BILLABLE. Entries to date: none.
Neck pocket. Do not operate the INSTRUMENT with the pocket empty.
| Audio specimens | Status | |
|---|---|---|
| A | Neck (24) | Not recorded |
| B | Bridge (22) | Not recorded |
| C | Both | Not recorded |
Specimens will be recorded on the first unit produced.
Manufacture and custody
Procedure JPI-M-1TMade by hands and machines in Portland, Oregon.
- Body (10), of one or two pieces, machined in two setups: top, then back.
- Bevels cut with a 1/4 in ball-nose.
- Neck (40) made to the Corporation’s pattern on a standard heel, and bolted.
- Hardware fitted per Sheet 2.
- On production, the serial is entered in the ledger. No entry has been made.
| Doc. 1 | Machining package: body, neck and board STEP and STL, setup DXFs, headstock template. | ZIP |
| Doc. 2 | Build notes. | MD |
| Doc. 3 | Headstock face template. | DXF |
| Ref. 1 | The solid-body instrument of the T type, first produced in the previous century, from which this filing takes its pickups, bridge plate and controls. | Items 20–34 |
| Ref. 2 | Neck pocket and heel of the standard pattern. | Item 40 |
The Corporation claims nothing taught by the prior art. The precedent stands.
Allocation
Units: none.
None allocated. Entries are held on file until the designation is released. Fee: to be determined. It has not been determined.
The instrument described in this case file is made by hands and machines in Portland, Oregon, by the builder of record, who has read the drawings and agrees with them. Each instrument carries his signature. Correspondence: [email protected], or on Instagram, @juris_instruments.
Non-billable hours: no upper limit has been established.